How do I simulate a transmission line?

Open this page and use the live Power Supply Designer tool below — set your inputs and the simulation runs instantly in your browser using real numerics. No install, no account needed.

Yes. The simulation runs free in your browser. A one-time unlock or a Pro plan adds advanced parameters, saved presets, data import, and clean exports.

Can I use my own numbers?

Absolutely — every input is adjustable, and with data import you can drive a transmission line from your own measurements.

Use case · powered by Power Supply Designer

Power Supply Designer for a transmission line

Simulate a transmission line live in your browser. This runs the real Power Supply Designer solver — adjust the inputs, watch it respond instantly, and export the result. No install, no account.

For:Students Researchers Educators Engineers Hobbyists & Makers K-12 Students First Responders

RLC Circuit

open full solver →

RLC Circuit StudioLive

series RLC step response

Controls

Apply a step voltage to a series RLC circuit and watch charge and current respond — under-, over-, or critically damped.

Presets

Resistance R

Inductance L

Capacitance C

▶ Run in Python

Data Inspector

Damping ζ0.750

Regimeunderdamped

ω₀1.000

Governing equation

1 \overset{q}{¨} + 1.5 \overset{q}{˙} + \frac{q}{1} = V_{0}, ω_{0} = \frac{1}{L C} = 1.000, ζ = \frac{R}{2} \frac{C}{L} = 0.750

Reading this result: ζ = 0.750 < 1: underdamped. With ω₀ = 1.000 rad/s the charge overshoots and rings, oscillating while it decays toward its steady value. Lower ζ means more ringing.

Runs locally in your browser — free forever. Scale to the cloud when reality gets heavy.

↓

Filter Designer

open full solver →

Analog Filter DesignerLive

RC & RLC frequency response

Controls

Presets

Resistance R (Ω)

Capacitance C (nF)

Passive filters shape a signal's frequency content with resistors, capacitors, and inductors. An RC low-pass or high-pass has a cutoff at 1/(2πRC) where the response drops 3 dB; an RLC bandpass resonates at 1/(2π√(LC)) with sharpness set by its quality factor Q.

▶ Run in Python

Data Inspector

Cutoff fc1.6 kHz

Resonance f₀5.0 kHz

Quality factor Q0.32

Governing equation

∣ H (f) ∣ = \frac{1}{1 + ( f /1592 ) ^{2}}

Reading this result: Low-pass: signals below the 1.6 kHz corner pass, above it they roll off at 20 dB/decade, and the response is exactly 3 dB down right at the corner.

Runs locally in your browser — free forever. Scale to the cloud when reality gets heavy.

↓

Thermal Resistance

open full solver →

Composite Wall Heat TransferLive

R-value & U-value

Controls

Presets

Drywall (mm)

Insulation (mm)

Brick (mm)

Inside temp (°C)

Outside temp (°C)

Heat flows through a wall like current through resistors in series. Each layer's thermal resistance is its thickness over its conductivity; adding them gives the total R-value, and the heat flux is the temperature difference divided by it. Insulation, with very low conductivity, dominates the R-value — the steep temperature drop shows where it does its work.

▶ Run in Python

Data Inspector

Total R-value2.71 m²K/W

U-value0.37 W/m²K

Heat flux9.6 W/m²

Governing equation

R = \sum \frac{L _{i}}{k _{i} A} = 2.71 \frac{m ^{2} K}{W}, Q = \frac{Δ T}{R} = 9.6 \frac{W}{m ^{2}}

Reading this result: The insulation layer carries the most thermal resistance, so the temperature falls most steeply across it. A total R-value of 2.71 m²K/W lets 9.6 W/m² flow for this 26°C difference.

Runs locally in your browser — free forever. Scale to the cloud when reality gets heavy.

or unlock everything with Pro →

About this simulation

The full Power Supply Designer tool models a transmission line with the same numerics engineers and scientists use — running entirely client-side. Change any parameter and the result updates in real time, so you can build intuition, check a design, or teach the concept without spreadsheets or installs.

More you can do with Power Supply Designer

Power Supply Designer for an RLC circuit Power Supply Designer for a power supply Power Supply Designer for a transformer Power Supply Designer for a DC motor Power Supply Designer for an op-amp filter Power Supply Designer for an antenna Power Supply Designer for a PCB trace Power Supply Designer for a battery pack

Other ways to simulate a transmission line

Fourier Transform for a transmission line Bode Plot for a transmission line Filter Designer for a transmission line PID Controller for a transmission line Transmission Line for a transmission line Op-Amp Circuits for a transmission line

Frequently asked questions

How do I simulate a transmission line?: Open this page and use the live Power Supply Designer tool below — set your inputs and the simulation runs instantly in your browser using real numerics. No install, no account needed.
Is it free?: Yes. The simulation runs free in your browser. A one-time unlock or a Pro plan adds advanced parameters, saved presets, data import, and clean exports.
Can I use my own numbers?: Absolutely — every input is adjustable, and with data import you can drive a transmission line from your own measurements.